GALGA Try it free

WHAT'S NEW

What changes in every version.

GALGA PMI is in its pilot phase. Here is what each version brings, and what is not there yet.

Versions 0.22 to 0.24.1 · October 2026

  • Mould review: slides (angle pin, locking heel and stroke) and sub gates (tip, cone and minimum Ø).
  • General tolerance: ISO 20457:2026, with the edition the drawing cites, and a warning when ISO 2768 is applied to a plastic part. If the drawing declares none, the customer profile or the standard one applies, always with a warning to confirm it.
  • Audit of integrity and confidentiality before every release.

Versions 0.15.2 to 0.21 · October 2026

  • Mould review: conformal channels, minimum water flow, moulding areas without nearby cooling, water near slides and inserts, thin steel, buckling ejector pins, draft for texture and venting by material.
  • Gauges and poka-yokes: the part turned 180° and clamps pushing the part sideways.
  • Tool record: ID with check character, STEP fingerprint, technical status and part revision, in JSON and Excel.

Version 0.15 · October 2026

  • The part inside the mould, measured on the exact model: minimum local draft with the area below it, sharp inner edges, steel left inside the part after the 3D operations, and ejectors too close to the edge.
  • Every check states how much it evaluated. If it evaluated nothing, it comes out as a failure, never as passed.
  • Distances from the water to the moulding surface are measured on the exact model, not on the mesh.

Versions 0.13.8 to 0.14 · October 2026

  • Verifiable closure of every finding of the mould review.
  • Mould acceptance sheet with the SHA-256 fingerprint of every file, and technical record of the mould.
  • Your mould manual in the review: every finding shows its section.
  • Hot runner, standard parts recognised by their geometry and matched to your catalogue, correction loops T0, T1… and the toolmaker's quote against the delivered mould.
  • 3-2-1 alignment plan from the PMI datums for the scanner or CT.
  • Every balloon in the Excel opens its characteristic in the 3D viewer.

Versions 0.12 to 0.13 · October 2026

  • Review of checking fixtures and gauges against the part PMI.
  • Part version change: where it changes, which datums it touches, which version the mould is made on and which steel parts must be reworked.

Versions 0.9 to 0.11 · October 2026

  • Automatic 2D mould drawings: every part with its function and every hole with what it does, cooling layout and machining hours.
  • Live 3D mould drawing and automatic review before the drawings are released.
  • CAD navigation and 3D mouse in every viewer.

Version 0.8.10 · October 2026

  • Results sheet for the German EMPB, in German, with i.O. / n.i.O. calculated.
  • The program contains no network code: the buy button opens your browser through the operating system.

Version 0.8.9 · October 2026

  • New name: GALGA PMI.
  • Units in every value column of the PPAP, AS9102 and control plan sheets.
  • Visible draft notice on every sheet until Quality approves it.

Versions 0.8.6 to 0.8.8 · September 2026

  • Viewer and report in Spanish, English, German, French, Italian and Portuguese.
  • General tolerances (DIN 16742, ISO 20457, ISO 2768) from the table each customer loads: the program never invents standard values.
  • Automatic «no leaks» test before every release: the viewer opens with no network requests and no output reveals which folder the file came from.

Versions 0.8.1 to 0.8.5 · September 2026

  • Location of every characteristic on the part, with the affected face highlighted and its coordinates.
  • 2D drawing views with balloons and feature control frames in the report.
  • Report in your company's name, with your logo.

Coming next

  • Automatic drawings with pockets, radii and sections.
  • Siemens NX 3D PDF reading with fewer characteristics to check.
  • Measurements shown on the 3D model (Halo mode), in development with pilot customers.
  • The submarine gate measured automatically and checked against the filling report.
  • QIF tested with the main measuring machines.
  • Export in the format of toolroom management programs.

Born in Valencia

Fast as a greyhound. Exact as a gauge.

GALGA was born in Valencia, in the automotive industry. It was built by design and production engineers with more than twenty years in moulds, injection moulding, gauges and dimensional inspection. Every launch started the same way: the customer’s 3D model, hundreds of dimensions and someone typing them into a spreadsheet by hand. We built it so we could stop doing that.

  • 20+years across moulds, injection moulding and dimensional inspection
  • 0made-up dimensions: anything doubtful is flagged

The galgo

The galgo, the Spanish greyhound: fast when it counts, calm and dependable the rest of the time. Minutes where there used to be hours, without the rush that leads to mistakes.

The gauge

On the shop floor, the galga (Spanish for gauge) is the reference master every part is compared against. GALGA is that for your data: one single reference for everyone.

Shop-floor rigour and a human touch.

Try it yourself or send us your part.

  • An engineer replies. A real person who knows the trade, not a bot, within 24 hours.
  • No small print. Published prices and clear terms from day one.
  • Your files, protected. With the licence they never leave your company; with the service, an NDA and documented deletion.

Licence: 7 days free, no card required, with a sample part so you can get started in a minute. Service: we sign an NDA, you send us a part number and within 48 hours you have the package, reviewed.

Try it yourself · 7 days freeSend us your partTalk to an engineer